Podcast loudness, every figure sourced
What LUFS Should a Podcast Be? −16 LUFS, and Why
What LUFS should a podcast be? −16 LUFS integrated with the true peak under −1 dBTP, the level Apple Podcasts recommends; −19 LUFS is commonly used for a mono file. Spotify and YouTube publish no podcast figure. The free tool above measures each episode and sets it there, in your browser, with nothing uploaded.
- −16 LUFS, Peaks Under −1 dBTP
- Each Figure With Its Source
- Free Normalizer, Nothing Uploaded
- Up to 20 Episodes at Once
Demo: a clean voice recording whose level we changed on purpose.
Target loudness
Spotify for Artists: tracks are played at −14 LUFS; masters under −1 dBTP · Peaks held under −1.0 dBTP by a true-peak limiter.
Drop one file or a whole batch
MP3, WAV, M4A, FLAC, OGG, MP4, MOV, WEBM · up to 20 files, 30 minutes and 400 MB each. Processed in your browser; nothing is uploaded.
Runs in your browser. Files never leave your device.
Up to 30 min · 400 MB
- Apple Podcasts, ±1 dB
- −16 LUFS
- true-peak ceiling Apple asks for
- −1 dBTP
- commonly used for mono
- −19 LUFS
- Spotify music, YouTube by practice
- −14 LUFS
- EBU R 128 broadcast
- −23 LUFS
- measure and set it, no upload
- Free
Podcast Loudness Targets, Platform by Platform
Which figures are published rules and which are common practice, and where each one comes from.
How to Set Podcast LUFS in 3 Steps
With the free normalizer above: no account, nothing uploaded, up to 20 episodes at once.
- 01
Measure the episode
Drop your files. Each one is measured for integrated loudness and true peak after ITU-R BS.1770, so you see how far it sits from the target.
- 02
Pick −16 or −19 LUFS
Choose −16 for Apple and stereo shows, or −19 if your show is mono and you follow that practice. Keep the peak limit at −1.0 dBTP.
- 03
Normalize and download
Play any row to check it, then save MP3 or WAV one by one, or all of them as a ZIP.
Podcast LUFS Example: Three Episodes, Two Targets
Demo episodes, set by the tool on this page when you press play. Pick one and switch between Original and Normalized.
A quiet episode, set to −16 LUFS
Lifted 15.0 dB with the true peak at −1.5 dBTP, so the limiter never had to act.
Demo: a clean voice recording whose level we changed on purpose. The result is made by the tool on this page, in your browser, when you press play.
Preview plays at half volume.
The quiet episode starts at −31.0 LUFS and needs 15.0 dB to reach −16, its true peak landing at −1.5 dBTP, so the limiter never acts. The mono episode needs only 1.0 dB to reach −19. The uneven interview reaches −16, but its loudness range stays 12.3 LU: one gain can’t even out two speakers.
Podcast Loudness, Explained Simply
What LUFS measures
LUFS is loudness as people hear it, measured after ITU-R BS.1770: the sound is weighted the way the ear is, and near-silent gaps are left out. The integrated figure covers the whole episode, so a podcast LUFS target means the full file, not its loudest minute. To read every figure of one file, use the LUFS meter.
Why true peak matters too
Peaks between samples can go over full scale once the file is turned into MP3 or AAC. A true-peak ceiling of −1 dBTP leaves room for that, which is why Apple pairs it with −16 LUFS. The tool above holds it with a limiter that only touches the loudest peaks.
Why not as loud as possible?
Pushing a voice well past −16 LUFS means squashing its peaks, and apps that level what they play may turn it down again. Much quieter than −16, and listeners reach for the volume between your show and the next one.
Common podcast loudness mistakes
What goes wrong most often:
- 1Judging by the peak meter: two files peaking at −1 dB can differ by several LU.
- 2Setting the level before removing noise: hum counts toward loudness. Clean first with the podcast enhancer.
- 3Expecting one gain to level a quiet guest: that needs a compressor or an edit.
- 4Changing the target every week: pick −16 or −19 and keep it.
A season to fix at once? The normalizer above takes 20 files and gives them back as a ZIP. For one file with every option explained, see normalize audio.
Frequently Asked Questions
Targets, platforms, mono or stereo, and setting the level.
−16 LUFS integrated with the true peak under −1 dBTP, the level Apple Podcasts recommends (±1 dB). For a mono file, −19 LUFS is commonly used instead.
Spotify’s podcast specification gives no loudness figure, so there is no official Spotify podcast loudness. Its published −14 LUFS is for music tracks. A −16 LUFS master with peaks under −1 dBTP is a common choice for every app.
Around −16 LKFS with a ±1 dB tolerance and a true peak not over −1 dB FS, measured after ITU-R BS.1770-5 and applied before encoding. MP3 can be mono or stereo; WAV and FLAC must be stereo.
YouTube publishes no target. −14 LUFS with peaks under −1 dBTP is commonly used for videos, so a video podcast often gets a −14 version for YouTube.
Both are in use. Apple’s −16 applies to the file as measured, mono or stereo. −19 is the common practice for mono files, so it sounds as loud as −16 in stereo. Pick one and keep it for every episode.
No single one. Apple’s −16 LKFS is the closest thing; the broadcast standards (EBU R 128 at −23 LUFS, ATSC A/85 at −24 LKFS) are for radio and TV.
Yes, one unit under two names. Apple writes LKFS, most tools write LUFS, and −16 means the same in both.
Drop the episode in the free normalizer above, pick −16 LUFS, keep the peak limit at −1.0 dBTP and download. It runs in your browser; nothing is uploaded.
For podcast apps it sits 2 LU above Apple’s target, outside its ±1 dB, and it often takes limiting to get there. For YouTube it is the common value.
Yes. Integrated loudness covers the whole file: voice, music and ads together. Measure the final mix, not the voice track alone.
The level change doesn’t. The limiter only acts when a target would push a peak past −1 dBTP; WAV adds no further loss, MP3 is a new encode at 192 kbps.
Set Your Podcast Loudness to −16 LUFS
What LUFS should a podcast be? −16, peaks under −1 dBTP. Drop your episodes above and download them there, free, with nothing uploaded.