Skip to content

Audacity 3 steps, checked against its manual

Audacity Noise Reduction, Step by Step

Audacity noise reduction takes two passes: Get Noise Profile on a few seconds of pure noise, then Noise Reduction on the track (6 dB, sensitivity 6, smoothing 6). It suits steady hiss and hum. For wind, traffic or voices, the AudioCleaner tool above takes one pass.

How it works
  • Steps From the Audacity Manual
  • Settings That Avoid Artifacts
  • Free Tool for Steady Noise
  • AI for Wind and Voices
  • Nothing to Install

A travel vlog on a windy ferry deck

Wind and engine · Vlog · Clean

Made noisy on purpose and cleaned on our partner studio, as it came out. The page lines the tracks up so you can switch while it plays.

0:00 / 0:00

Cleaned: AI Clean took the noise out and kept the voice as it was.

Noise removed100%

Below 100% a little of the place comes back, for a natural sound. Free to change.

Playback here is matched to it, so the comparison is fair.

Your files and results are visible only to you; runs are kept 7 days.

Up to 30 min · 400 MB

noise profile, then reduce
2 passes
default dB, sensitivity, smoothing
6 · 6 · 6
hear only what will be removed
Residue
repeat it on the next selection
Ctrl+R
hiss, hum, fans; not traffic
Steady noise
with the tool above, no profile
1 pass

How to Remove Background Noise in Audacity

The steps and menu names come from the Audacity 3 manual. To have Audacity remove background noise, it first needs to hear the noise alone.

  1. 01

    Select pure noise

    Find a few seconds where nobody speaks, only the hum or hiss, and drag over it. The manual asks for at least 2048 samples (about 0.05 s); a longer stretch gives a better profile.

  2. 02

    Get Noise Profile

    Choose Effect > Noise Removal and Repair > Noise Reduction and click Get Noise Profile. Audacity keeps that noise as the profile until you close it.

  3. 03

    Select the track and set it

    Select all the audio to clean (Ctrl+A), open Noise Reduction again and set Noise reduction (dB), Sensitivity and Frequency smoothing (bands). Click Preview, and switch Noise to Residue to hear only what would go.

  4. 04

    Apply and listen

    Set Noise back to Reduce and click OK. Play the quiet parts and the words; if the voice sounds watery, undo and try gentler values. Then export.

Audacity Noise Reduction Settings, One by One

Noise reduction in Audacity comes down to one profile and three sliders. What each control does, its default, and the sign that it has gone too far.

Beyond Noise Reduction in Audacity: A Drill Next Door

The class sample in the tool above: a teacher with a drill starting and stopping next door. Noise that comes and goes is what the manual says a profile does not suit.

An online class with a drill next door

The drill starts and stops, so no single profile fits it. Clean follows it and keeps the teacher.

Our sample: made noisy on purpose and cleaned on our partner studio.

Original
100%
More naturalMore removal
Mixes the original back in, live in your browser; nothing is processed again. The [ and ] keys change it.
Noise in the pauses
-25 dB-66 dB
Voice level
-13.5 dB-13.3 dB

Run with Clean, the pauses fell from about -25 dB to about -66 dB across the file, while the voice stayed at about -13.5 dB. The Removed track is the drill on its own, at about the same level under words and pauses, with no profile taken.

Robotic or watery voice

The most common complaint. Those warbles are the short random tones the manual calls musical noise, and they come from Sensitivity set too low or a profile that does not match the noise everywhere. Raise Sensitivity a step, lower Noise reduction, or add Frequency smoothing. The Audacity support guide also suggests a lighter Noise Reduction followed by Effect > Noise Removal and Repair > Noise Gate.

The noise changes during the file

A profile is a snapshot. If a fan speeds up, a car passes or the hiss changes along a cassette, parts of the file no longer match it. To remove background noise in Audacity from a file like that, take a new profile for each section and apply it there; for noise that never holds still, a fixed profile is the wrong tool.

Hum and whistles survive

A narrow tone hides right next to the voice. Notch it first (60 Hz in North America, 50 Hz in most other countries, and each harmonic), then reduce background noise in Audacity with a light pass for what is left.

When the tool above is faster

Wind, traffic, a café, other people talking and room echo change from moment to moment, and the manual says the profile method does not suit irregular noise. Drop the file in the tool above, pick the noise, and Clean or Studio voice handle it in one pass, with no profile to take. For a ringing room, the echo remover is built for it.

Work on a copy. Export the original first, so a heavy pass can always be undone, even after you close the project.

Audacity Noise Reduction FAQ

Settings, problems, and when to use something else.

Beyond Audacity Noise Reduction: One Pass

Drop the file above, pick the noise, and hear it cleaned with no profile to take: free for steady noise, AI for wind, traffic and voices.